search

Digital ID View 960H Series Manual de usuario Pagina 14

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 61
  • Tabla de contenidos
  • MARCADORES
    • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 13
Digital Video Recorder for Ness IQ-
Series
1.5.11 USB Connections
There are up to
four identical USB ports in front and in rear. It is possible to connect a USB memory stick to archive data or
a mouse to control the device.
1.5.12 RS-232 Connections
This port is not in use for users. Do not connect any devices
CAUTION
W
HEN USING THE RS232 SERIAL PORT, USERS MUST REQUEST FOR ASSISTANT TO QUALIFIED TECHNICAL PERSON OR
SERVICE REPRESENTATIVE.
1.5.13 Grounding (Earthing)
Connection of ground wire is highly recommended to protect the DVR from external
electrical surge.
1.5.14 Factory Reset Switch
Reset the switch to restore all setup values of menus to factory default settings. It is also
Log file.
The switch is located in a pin hole of the back panel.
Put the clip pin into the switch hole on the monitor (Live) screen and keep pressing until the switch has clicked.
CAUTION
P
RESS FACTORY RESET SWICH ONLY IN LIVE MODE
1.5.15
Power Supply connections
4 / 8 Channel:
960H & 4 Channel SDI
to ’DC12V
’ connector and plug another side to
Please do not use any different power supply adapter because it may cause the DVR to malfunction.
16 Channel
960h & 8 / 16 Channel SDI
to ’DC12V
’ connector and plug another side to power source. Adapter input voltage is a free volt (100 VAC ~ 240 VAC).
Please do not use any different power supply adapter because it may cause the DVR to malfunction.
1.5.16 Connections Guideline
Video Out Connector:
If only the monitor is connected to
rear side of the monitor to 75 ohms to prevent abnormally bright or collapsed images.
a recorder) to the back of the monitor, please set the impedance switch on the rear side of the monitor to
Impedance) and set the last device to 75 ohms.
Alarm Input Connector:
Do not input any type of voltage to the AI 1~AI
Series
960H & SDI DVR
four identical USB ports in front and in rear. It is possible to connect a USB memory stick to archive data or
This port is not in use for users. Do not connect any devices
through this port.
HEN USING THE RS232 SERIAL PORT, USERS MUST REQUEST FOR ASSISTANT TO QUALIFIED TECHNICAL PERSON OR
Connection of ground wire is highly recommended to protect the DVR from external
electri
c shock, such as lightening,
Reset the switch to restore all setup values of menus to factory default settings. It is also
possible to use to initialize System
The switch is located in a pin hole of the back panel.
Put the clip pin into the switch hole on the monitor (Live) screen and keep pressing until the switch has clicked.
RESS FACTORY RESET SWICH ONLY IN LIVE MODE
NEVER PRESS IN SETUP MODE.
Power Supply connections
960H & 4 Channel SDI
Plug the power supply adapter (DC 12V, 5A)
which include in this product
’ connector and plug another side to
power source. Adapter input voltage is a free volt (100 VAC ~ 240 VAC).
Please do not use any different power supply adapter because it may cause the DVR to malfunction.
960h & 8 / 16 Channel SDI
: Plug the power supply adapter (DC 12V, 6.67
A)
’ connector and plug another side to power source. Adapter input voltage is a free volt (100 VAC ~ 240 VAC).
Please do not use any different power supply adapter because it may cause the DVR to malfunction.
If only the monitor is connected to
VIDEO OUT connector, please set the impedance switch on the
rear side of the monitor to 75 ohms to prevent abnormally bright or collapsed images.
If wish to connect another devi
a recorder) to the back of the monitor, please set the impedance switch on the rear side of the monitor to
Impedance) and set the last device to 75 ohms.
Do not input any type of voltage to the AI 1~AI
4 (AI 16) connectors.
Page
14
four identical USB ports in front and in rear. It is possible to connect a USB memory stick to archive data or
HEN USING THE RS232 SERIAL PORT, USERS MUST REQUEST FOR ASSISTANT TO QUALIFIED TECHNICAL PERSON OR
c shock, such as lightening,
possible to use to initialize System
Put the clip pin into the switch hole on the monitor (Live) screen and keep pressing until the switch has clicked.
which include in this product
power source. Adapter input voltage is a free volt (100 VAC ~ 240 VAC).
Please do not use any different power supply adapter because it may cause the DVR to malfunction.
A)
which include in this product
’ connector and plug another side to power source. Adapter input voltage is a free volt (100 VAC ~ 240 VAC).
Please do not use any different power supply adapter because it may cause the DVR to malfunction.
VIDEO OUT connector, please set the impedance switch on the
If wish to connect another devi
ce (e.g.,
a recorder) to the back of the monitor, please set the impedance switch on the rear side of the monitor to
HIGH Z (High
Vista de pagina 13
1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 60 61

Comentarios a estos manuales

Sin comentarios
  • Shop fox DEGEN Beef Eater Anli Burk
  • AEG Taladros Eléctricos Electrolux Gradas de equipos AV Philips Accesorios De Cocina Y Artículos Para El Hogar Porter-Cable Compresores de aire NEC Soportes De Pared Para Pantalla Plana
  • Electrolux EOC3410COX Warn M15000 DeWalt DW007 Samsung GT-S3100 Digital Loggers Personal Call Recorder
  • August DA100C Manual de usuario Huawei HUAWEI P10 Manual de usuario Acer ICONIA Manual de usuario Nikon EH-4 Manual de usuario Philips BT3500B-37 Manual de usuario